
Hours, not years
A strip light is rated in hours, and a shop is rated in years. A strip rated at 30,000 hours runs eight hours a day for ten years, which means the rating rarely decides the failure. The same rule holds for a display case and a food kiosk, with the water rating mattering more at a food counter. We keep the alternative on the same quotation, so the buyer compares a number instead of a preference.
What fails first is not the chip. Heat, moisture and a bad driver end a strip long before its hours do, and silicone changes two of those three. That number belongs on the lighting schedule, because a choice agreed verbally rarely survives a service visit. Most of these failures appear in year two, which is exactly when the warranty conversation starts.
What silicone actually does
Silicone is the jacket, not the light. A silicone extruded strip wraps the PCB in a solid body, so water, oil and cleaning fluid cannot reach the circuit. Mark it on the drawing sheet too, so whoever services the shelf later has the reference without guessing. One wipe with a sanitiser settles the question faster than a page of datasheet reading.
An ordinary strip is a PCB with a thin resin coat. That coat passes a wipe and fails at a steam cleaner, and a kiosk near a food counter sees both in one shift. None of that shows in a render, which is why we send a metre of each strip to the site before the order. Clients who settle it at design stage pay nothing extra, and clients who settle it after opening pay a service call.
Choose a silicone strip where the jacket is extruded, not dipped. An extruded body is one piece and seals at the ends, and a dipped strip has a soft edge that lifts glass showcases. The same rule holds for a display case and a food kiosk, with the water rating mattering more at a food counter. We keep the alternative on the same quotation, so the buyer compares a number instead of a preference.
Dots or a line
An ordinary strip shows dots at 60 mm spacing. A silicone COB strip shows a continuous line at 3 mm chip pitch, and the difference shows on a polished counter. That number belongs on the lighting schedule, because a choice agreed verbally rarely survives a service visit. Most of these failures appear in year two, which is exactly when the warranty conversation starts.
Dotting matters on a display case. A case with a dotted strip puts a bright spot on every product edge, and the customer reads the pattern display cases. Mark it on the drawing sheet too, so whoever services the shelf later has the reference without guessing. One wipe with a sanitiser settles the question faster than a page of datasheet reading.
Heat and the driver
Both types produce the same heat per watt, so the difference is where it goes. A silicone body spreads heat along the run, and a bare PCB heats the shelf it sits on. None of that shows in a render, which is why we send a metre of each strip to the site before the order. Clients who settle it at design stage pay nothing extra, and clients who settle it after opening pay a service call.
Fit a driver rated 20 percent above the load. A kiosk that runs a 30 W strip on a 24 W driver loses a driver in a year, and a lost driver takes the whole shelf dark. The same rule holds for a display case and a food kiosk, with the water rating mattering more at a food counter.

Water and cleaning
A silicone strip at IP65 takes a wipe with a sanitiser and a spill at a food counter. An IP20 strip at a food kiosk fails within weeks, because sanitiser reaches the circuit through the coat. We keep the alternative on the same quotation, so the buyer compares a number instead of a preference. That number belongs on the lighting schedule, because a choice agreed verbally rarely survives a service visit.
Use IP65 on every strip inside a case or at a food counter, and IP20 only on a shelf inside a dry shop. The price gap is small against one replacement visit. Most of these failures appear in year two, which is exactly when the warranty conversation starts. Mark it on the drawing sheet too, so whoever services the shelf later has the reference without guessing.

Cost per metre
A silicone COB strip costs about twice an ordinary strip of the same output. On a 60 sqm shop with 40 m of shelf lighting, that difference buys less than one service call. One wipe with a sanitiser settles the question faster than a page of datasheet reading. None of that shows in a render, which is why we send a metre of each strip to the site before the order.
Count the whole cost, not the metre. A cheaper strip that fails in year two costs the strip, the labour, the shelf removal and a week of shop fixtures. Clients who settle it at design stage pay nothing extra, and clients who settle it after opening pay a service call. The same rule holds for a display case and a food kiosk, with the water rating mattering more at a food counter.
The comparison that matters
The table below is the comparison we use on a quotation, and it holds at a normal shop duty cycle of eight hours. We keep the alternative on the same quotation, so the buyer compares a number instead of a preference. That number belongs on the lighting schedule, because a choice agreed verbally rarely survives a service visit.
| Item | Silicone COB | Ordinary SMD |
|---|---|---|
| Rated hours | 30,000 | 25,000 |
| Appearance | Continuous line | Dots at 60 mm |
| Water rating | IP65 to IP68 | IP20 to IP44 |
| Bend radius | 30 mm | 100 mm |
| Cost per metre | 1.9 times ordinary | baseline |
Where an ordinary strip is fine
An ordinary strip belongs inside a dry shelf, behind a fascia, or under a counter where nobody wipes. In those places the silicone body adds cost and no benefit. Most of these failures appear in year two, which is exactly when the warranty conversation starts. Mark it on the drawing sheet too, so whoever services the shelf later has the reference without guessing.
Use the cheap strip where the light never meets a hand. A shop that puts silicone everywhere pays for protection it does not use, and that money cash counters. One wipe with a sanitiser settles the question faster than a page of datasheet reading. None of that shows in a render, which is why we send a metre of each strip to the site before the order.
Match the profile to the strip. A 12 mm silicone body needs a 15 mm channel, and a 10 mm channel takes an ordinary strip only, so the profile is counters and towers. Clients who settle it at design stage pay nothing extra, and clients who settle it after opening pay a service call. The same rule holds for a display case and a food kiosk, with the water rating mattering more at a food counter.

Colour and output
Both types come in 2700 to 4000 K, and both run 12 or 24 V. Choose 24 V for a run over 3 m, because a 12 V run drops brightness at the far end. We keep the alternative on the same quotation, so the buyer compares a number instead of a preference. That number belongs on the lighting schedule, because a choice agreed verbally rarely survives a service visit.
Set the output to 1200 lux at the shelf face for retail, and 500 lux for ambient. A shelf lit at 2000 lux flattens the product, and a shelf at 400 lux disappears fixture materials. Most of these failures appear in year two, which is exactly when the warranty conversation starts. Mark it on the drawing sheet too, so whoever services the shelf later has the reference without guessing.

Conclusion
Silicone buys water protection, a continuous line and a tighter bend. An ordinary strip buys cost and covers a dry shelf just as well. One wipe with a sanitiser settles the question faster than a page of datasheet reading. None of that shows in a render, which is why we send a metre of each strip to the site before the order.
Put silicone where a hand or a cloth reaches, and ordinary strip where nothing does. That split keeps a shop lit for a decade without paying twice for the retail displays. Clients who settle it at design stage pay nothing extra, and clients who settle it after opening pay a service call. The same rule holds for a display case and a food kiosk, with the water rating mattering more at a food counter.
Check the connector, not only the strip. A silicone body needs a matching connector with a seal, and a bare connector at the end of a sealed strip is where water gets in. We keep the alternative on the same quotation, so the buyer compares a number instead of a preference. That number belongs on the lighting schedule, because a choice agreed verbally rarely survives a service visit.
