Avada Car Dealer News

A 3D design costs 1 percent

A 3D design for a kiosk costs 3,000 yuan and the fit costs 300,000. One percent buys the only drawing that shows a 900 mm top against a 1,650 mm customer eye. Mark it on the drawing sheet too, so whoever moves a case later has the reference without guessing. One factory visit settles the question faster than a week of revision rounds.

A shop built without a 3D drawing changes 3 to 5 details on site and each change is 2,000 yuan plus a week. One percent saves 10,000 and retail displays. None of that shows in a render alone, which is why we mark heights and clearances on the sheet. Owners who settle it at design stage pay nothing extra, and owners who settle it after a cut pay a re-panel.

The 5 errors a 3D catches

A 3D catches 5 errors: a case at the wrong height, a counter too shallow, a light that reflects into an eye, a door that opens into a queue and a sign cut by a beam. The same rule holds for a kiosk and a shop front, with the eye height mattering in both. We keep the alternative on the same quotation, so the owner compares a section instead of a colour.

A case at 1,100 mm blocks a customer at 1,600 mm and a case at 900 mm does not. A 200 mm error is a 3,000 yuan rebuild kiosk design. That number belongs on the drawing set, because a dimension agreed verbally rarely survives the factory cut. Most of these gaps appear at the first installation, which is exactly when the site is tightest.

Height, eye and the 900 mm

A 3D render at eye level shows what a customer sees at 1,600 mm from a counter 900 mm high. A 900 mm counter puts a top 700 mm below an eye and a 1,100 mm puts it 500 below. Mark it on the drawing sheet too, so whoever moves a case later has the reference without guessing. One factory visit settles the question faster than a week of revision rounds.

A 500 mm drop reads a tray flat and a 700 mm drop reads it at an angle. An angle at 30 degrees shows a ring face and a flat tray shows a glass showcases. None of that shows in a render alone, which is why we mark heights and clearances on the sheet. Owners who settle it at design stage pay nothing extra, and owners who settle it after a cut pay a re-panel.

Depth and the 700 mm

A 3D section shows a 700 mm top with a 600 mm back worktop and a 300 mm drawer under it. A 500 mm top hides a shaker and a 600 mm back hides a boiler. The same rule holds for a kiosk and a shop front, with the eye height mattering in both. We keep the alternative on the same quotation, so the owner compares a section instead of a colour.

A section view catches a drawer that opens into a staff leg. A drawer at 300 mm needs 400 mm of open space and a drawing without a section misses it shop fixtures. That number belongs on the drawing set, because a dimension agreed verbally rarely survives the factory cut. Most of these gaps appear at the first installation, which is exactly when the site is tightest.

case depth

Draw the case depth against a tray size. A 400 mm case takes a 300 mm tray and a 350 mm case takes a 300 mm tray only if the glass sits at 8 mm, so counters and towers. Mark it on the drawing sheet too, so whoever moves a case later has the reference without guessing.

white model kiosk

Seven numbers before a cut

The table is what a 3D drawing must carry before a factory cuts a panel, and each line answers a height, a depth or a clearance rather than display cases. One factory visit settles the question faster than a week of revision rounds. None of that shows in a render alone, which is why we mark heights and clearances on the sheet.

Item Number
Design fee 3,000 yuan
Fit cost 300,000 yuan
Counter height 900 mm
Customer eye 1,600 mm
Top depth 700 mm
Drawer clearance 400 mm
Tray tilt 30 degrees
wood kiosk model

Light and the 3,000 K test

A 3D with a light pass shows a 3,000 K spot at 400 lux on a tray. A render without a light pass ships a 5,000 K strip and a strip at 5,000 K turns gold to brass. Owners who settle it at design stage pay nothing extra, and owners who settle it after a cut pay a re-panel. The same rule holds for a kiosk and a shop front, with the eye height mattering in both.

A spot at 200 mm from a lid leaves 400 lux on a tray and a spot at 60 mm leaves 1,200, which is a glare panel at a customer eye and a burn on a leather prop cash counters. We keep the alternative on the same quotation, so the owner compares a section instead of a colour.

The 2 week sequence

A 3D sequence takes 2 weeks: 3 days for a block model, 3 for a light pass, 3 for a material pass and 5 for a factory drawing. A cut starts after the 4th pass and not before. That number belongs on the drawing set, because a dimension agreed verbally rarely survives the factory cut. Most of these gaps appear at the first installation, which is exactly when the site is tightest.

A factory that cuts from a block model cuts 1 in 5 panels wrong. Five panels at 2,000 yuan is 10,000 and the render fee was 3,000, so the render is the service kiosk. Mark it on the drawing sheet too, so whoever moves a case later has the reference without guessing. One factory visit settles the question faster than a week of revision rounds.

timber booth model

Conclusion

A 3,000 yuan 3D against a 300,000 fit, a 900 mm counter at a 1,600 mm eye, a 700 mm top, a 400 mm drawer clearance, a 30 degree tilt and a 3,000 K pass. Six lines protect a build. None of that shows in a render alone, which is why we mark heights and clearances on the sheet.

Cut glass and laminate only after the material pass. A render ordered before a cut is 1 percent of the budget and a rebuild ordered after a cut is 10 percent. Owners who settle it at design stage pay nothing extra, and owners who settle it after a cut pay a re-panel. The same rule holds for a kiosk and a shop front, with the eye height mattering in both.

fixture materials

Match a laminate sample to the render before an order. A laminate at 2 samples costs 200 yuan and a wrong lot costs a 4,000 yuan re-panel on a shop fit out. We keep the alternative on the same quotation, so the owner compares a section instead of a colour. That number belongs on the drawing set, because a dimension agreed verbally rarely survives the factory cut.

red roof model

Leave A Comment