UniqueKiosk · Shenzhen workshop

Vendor Cart in Steel With Rails and Open Counter

$2,300.00

Stainless food cart with an open service bay, railing bars and a fold-down shelf, sized 1.7 x 0.9 m for street vending. Price range: USD 2,000-6,600, set by size and open bay depth.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Open Service Bay

An open bay runs across the front of this food cart. The bay is 1,700 mm wide and 700 mm tall, with no glass. A railing of vertical stainless bars sits at the counter edge, spaced 60 mm apart. Bars stop goods sliding off while a vendor serves. Behind the bay, a full shelf line holds trays and tins. Buyers see the whole stock from the aisle. Every food cart we build for hot food uses this open bay. The food and drinks stall keeps steam clear with the same layout.

stainless vendor cart

Body and Wheels

A stainless body carries this food cart on two spoked wheels. The shell is 0.9 mm 304 sheet over a 25 mm frame. Spoked wheels are 400 mm with steel rims, set at the rear. A draw bar runs at the left for a second person to push. The body stands 900 mm to the counter, 1,900 mm to the roof cap. A small hatch sits at the lower left for a gas bottle. This food cart reads solid from the side. display cases glass can be added to the bay later.

vendor cart front view

Roof and Shelf

A sloped roof cap covers this food cart at 1,900 mm. The cap is folded sheet with a sealed edge, pitched to the back. A fold-down shelf drops on the right, 600 mm deep. The shelf takes bags and a card reader during a rush. A middle shelf sits inside the bay, split into two runs. Roof space holds a light bar if a vendor wires one. This food cart sheds rain away from the service face. cash counter counters use the same roof cap.

vendor cart side view

Build and Finish

Frame tubes are welded, then ground at every joint. Panels are folded so the corners have no gaps. Railing bars are cut on a jig and welded at equal spacing. Wheels are fitted with sealed bearings and a locking pin. Every food cart is assembled and levelled on a test floor. Shelf brackets are rated for 40 kg each. countertop cases cases can sit in the bay if a shop needs a cover. coffee fit-outs fit outs share the battery tray.

railing and open bay

Use on Site

Two people move this food cart on rough ground. Setup takes about 10 minutes: lock the wheels, drop the shelf. The footprint is 1.7 m by 0.9 m with the shelf down. Water and power are not built in, so a vendor brings a cooler. A 12 V light bar can run off a small battery. retail display fixtures spacing rules keep a gap at the wheels. This food cart fits a 2 m market bay.

Price and Custom Build

An open bay sells fast food quicker than a glass counter. Railing bars stop trays sliding when the cart is pushed. A fold-down shelf adds a packing point in a tight bay. List price starts at USD 2,300 for the 1.7 m build. A longer cart at 2.2 m with a glass bay lands near USD 3,100. ukiosks builds this food cart to order in Shenzhen. We can reset bay width, railing spacing, roof pitch and shelf depth. Send your plan and we return drawings and a quote. Nearby food and drinks kiosks and display cases counters share the same body frame.

Specification Detail
Overall size 1.7 x 0.9 x 1.9 m (custom 1.4-2.4 m)
Body 0.9 mm 304 stainless on 25 mm frame
Bay Open bay 1,700 x 700 mm
Railing Stainless bars, 60 mm spacing
Roof Folded stainless cap, rear pitch
Wheels Two 400 mm spoked wheels, draw bar
Packing One crate, about 90 kg

Reviews

There are no reviews yet.

Be the first to review “Vendor Cart in Steel With Rails and Open Counter”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop