UniqueKiosk · Shenzhen workshop

Trailer Food Cart in White With Blue Awning

$4,600.00

White towable food cart with a blue scalloped awning, three flip glass windows and a stainless ledge, sized 3.0 x 2.0 m. Price range: USD 2,000-6,600, set by size and fit out.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

White Body and Awning

White steel panels make the body of this food cart. The shell is 1.6 mm galvanised sheet on a 40 mm tube frame. Rounded lower corners soften the corners on a tight pitch. A blue scalloped awning spans the front at 2.1 m. The front face carries three service windows, each 900 mm wide. Diamond plate runs along the skirt below the wheel line. This food cart reads clean from 20 m on a street pitch. The food and drinks zone of a mall takes the same look.

white food cart trailer

Flip Windows and Ledge

Each window of this food cart flips up on a gas strut. The glass sits in an aluminium frame with a rubber seal. A stainless ledge folds down below the opening, 300 mm deep. Staff pass bags across it without reaching out. Closed, the windows lock flat and seal the cabin. Rain cannot reach the counter when the trailer sits idle. Every food cart we build keeps this ledge on the service side. display cases glass is the same 6 mm tempered grade.

food cart front window

Chassis and Running Gear

A steel chassis carries this food cart on tandem axles, set for low tow speed. Wheels are 13 inch with sealed bearings and steel fenders. Four screw legs drop at the rear to level the body on sloped ground. A draw bar sits at the front for a light tow vehicle. Brake lights and markers run off a 12 V plug. Gross weight lands near 1,100 kg empty. The body length is 3.0 m and the width is 2.0 m. cash counter counters inside need no extra frame.

food cart side view

Build and Fit Out

Panels are cut on a plasma table, then folded and welded to the frame. Seams get a seal bead and a paint coat. The awning is welded steel tube with a coated fabric skin. Windows are glazed and strutted in the shop. Every food cart is wired and water tested before crating. A sink, a griddle or a cold bin drops into the cabin of this food cart. countertop cases cases can sit on the ledge for a night market. coffee fit-outs fit outs use the same panel gauge.

flip window and ledge

Site Setup and Use

Setup takes two people and about 40 minutes. Level the legs, lock the brake, then open the windows. Water fills from a 20 L tank under the sink. A 16 A supply runs lights, a pump and one appliance. The cart suits street pitches, markets and park events. Closed, it tows behind a small van at low speed. retail fixture rules on pitch size apply in most cities. Footprint of this food cart is 3.0 m by 2.0 m with the awning out.

Price and Custom Build

A towable shell beats a fixed kiosk when a pitch changes by season. Flip windows keep stock covered between shifts. The blue awning gives shade without a full roof. List price starts at USD 4,600 for the 3.0 m shell with windows. A smaller push model at 2.2 m lands near USD 3,200. ukiosks builds this food cart to order in Shenzhen. We can reset body length, window count, awning colour and cabin fit out. Send your plan and we return drawings and a quote. Nearby food kiosks and countertop cases cases share the same frame.

Specification Detail
Overall size 3.0 x 2.0 x 2.4 m (custom 2.4-4.2 m)
Body 1.6 mm galvanised steel on tube frame
Windows Three flip glass windows, gas strut
Awning Welded tube frame with coated fabric
Chassis Tandem axle, 13 inch wheels, four screw legs
Power 12 V lights, 16 A cabin supply, 220 V
Packing One crate, about 1,100 kg

Reviews

There are no reviews yet.

Be the first to review “Trailer Food Cart in White With Blue Awning”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop