UniqueKiosk · Shenzhen workshop

Grill Cart in Stainless With Folding Canopy and Griddle

$3,400.00

Stainless towable food cart with two griddle plates, fold-out canopy panels and a water tap, sized 2.4 x 1.0 m. Price range: USD 2,000-6,600, set by size and cooking fit out.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Twin Griddle Deck

Two griddle plates sit on the open deck of this food cart. Each plate is 8 mm steel over a burner, 450 mm wide. Plates are set side by side at the back of the deck, away from the counter edge. A stainless water tap stands between them for wiping down. The deck measures 2.4 m by 1.0 m and holds a gas tray below. Heat runs off two burners under each plate. This food cart grills at 200 C within seven minutes. The food and drinks stand at a night market uses this deck.

stainless grill cart

Fold-Out Canopy

Fold-out panels form the canopy of this food cart. Two sheet panels hinge on posts and lift on gas struts. Open, the canopy spans 3.0 m and shades the whole deck. Closed, the panels lie flat over the body for towing. Post tops carry a small light bar socket. Shade keeps the cook cool and the plates even. Every food cart we build for grilling keeps the panels light enough for one person.

grill cart front view

Trailer Body

A stainless trailer body carries this food cart on one axle. The shell is 1.2 mm sheet over a 40 mm frame, with a double skin door line. A draw bar sits at the front with a jockey wheel for balance. A single 13 inch wheel sits under each side. Rear panels open for gas and stock. Body weight lands near 320 kg empty. This food cart tows at low speed behind a van. display cases glass can be added over one griddle.

grill cart side view

Build and Finish

Panels are folded from one sheet, so deck corners have no weld gap. Weld runs get a grind and a brush pass. Hinges on the canopy are stainless pin type, tested for 2,000 cycles. Gas lines are run in copper with a shut valve at the deck. Every food cart is assembled, wired and flame tested in the workshop. cash counter counters use the same gas tray. countertop cases cases fit the rear shelf for cold stock.

griddle plate and tap

Setup and Use

Two people set up this food cart in about 30 minutes. Level the jockey wheel, open the canopy, connect gas. Water fills a 15 L tank under the deck. A 16 A supply runs lights and a pump if fitted. The footprint is 2.4 m by 1.0 m closed, 3.0 m wide with panels open. Clean down is a scraper, a cloth and a tap rinse. retail display fixtures rules apply on pitch width and flame use. This food cart suits open air events.

Price and Custom Build

Two plates let one cook work while the other plate rests. Fold-out panels save the cost of a full roof frame. A tap on the deck cuts the walk for a wipe down. List price starts at USD 3,400 with the twin plates and canopy. A single plate cart with no canopy lands near USD 2,500. ukiosks builds this food cart to order in Shenzhen. We can reset deck length, plate count, canopy span and body colour. Send your plan and we return drawings and a quote. Nearby coffee fit-outs counters and food and drinks kiosks use the same deck frame.

Specification Detail
Overall size 2.4 x 1.0 x 1.9 m (custom 2.0-3.2 m)
Body 1.2 mm stainless on 40 mm frame
Griddles Two 8 mm steel plates, 450 mm each
Canopy Two fold-out panels on gas struts
Water 15 L tank with deck tap
Wheels Two 13 inch wheels, jockey wheel
Packing Two crates, about 320 kg

Reviews

There are no reviews yet.

Be the first to review “Grill Cart in Stainless With Folding Canopy and Griddle”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop