UniqueKiosk · Shenzhen workshop

Double Sided A3 Menu Light Box With Aluminum Base

$185.00

Double sided A3 light box for counter menus, 297 x 420 mm faces, with a slim aluminium frame and a wide angled base. Price range: USD 170-260, set by panel size and finish.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

A3 Counter Format

A wider face makes this light box a menu board first. The panel takes an A3 sheet at 297 x 420 mm. The frame is slim aluminium at 15 mm, so the print edge stays close to the glass. Height at about 620 mm puts the price line at standing eye level. The base is 300 mm wide and angled, so the unit does not walk when bumped. Two faces show the same menu to both sides of a counter. The unit weighs near 4 kg and moves with one hand. retail display fixtures teams test each panel for even light.

double sided menu light box

Two Face Lighting

Both faces of this light box carry their own strip, so one print never outshines the other. Each strip is an edge lit bar at 3000 K with a diffuser sheet on top. Panel brightness reaches about 1000 lux at the centre. A printed sheet sits between two acrylic panes, held by a snap strip. Staff swap a menu in about 30 seconds with no tool. A smear on the acrylic comes off with a soft cloth. The frame opening leaves a 6 mm white border around the print. display cases counters use the same strip.

menu light box front view

Angled Base

The base of this light box is a hollow aluminium extrusion, cut at an angle on both ends. A driver board and a small switch sit inside, away from the panel heat. A 1.5 m cable runs from the right side and can be routed behind a counter. Feet are four rubber pads with a 3 mm lift. The angled faces give the base a wedge look that matches timber counters. A longer base can be ordered for an A2 panel. Every countertop cases case gets the same pad lift. This light box ships with clear fitting notes.

menu light box side view

Build And Service

Frames for this light box are cut to the panel size and joined with corner keys. The acrylic panes are 3 mm with a polished edge and a clean cut. Strips are fixed on the frame rail, then wired to the driver in the base. Each unit runs a 30 minute light test before packing. A spare strip and two corner keys ship in the carton. The acrylic can be replaced on site without a new frame. Packing uses a foam sleeve and one carton. cash counter desks keep a spare key set. This light box ships with clear fitting notes.

aluminium base switch detail

Counter Uses

This light box suits a pizza counter, a juice bar and a coffee till. An A3 face fits a full price list with photos beside each line. The double face lets one board serve a queue on both sides. A wedge base sits well on a 600 mm counter with a till behind it. Cable routing keeps the serving area clear. The unit reads at 2 m, so a shopper spots the price before joining the line. Many shop fit outs use one per counter. food and drink shops often order three.

Price And Custom Build

List price starts at USD 185 for this A3 double sided unit. An A2 face with a wider base lands near USD 250. A menu board that lights both sides sells a full price list without extra prints. A wedge base stays put on a busy counter. A snap strip keeps a menu current with no tools. ukiosks builds this light box to order in Shenzhen. We can reset panel size, frame colour, strip warmth and base length. Send your plan and we return drawings and a quote.

Specification Detail
Panel size A3, 297 x 420 mm (custom A4-A2)
Frame 15 mm aluminium, silver
Faces Two 3 mm acrylic panes with snap strip
Light Edge lit LED at 3000 K, about 1000 lux
Base Angled aluminium with driver and switch
Cable 1.5 m lead from the right side
Packing One carton, about 4 kg

Reviews

There are no reviews yet.

Be the first to review “Double Sided A3 Menu Light Box With Aluminum Base”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop