
Fourteen days, nine steps
Paint display furniture runs 9 steps across 14 days, and a skipped sanding grit shows up as a 0.3 mm orange peel 6 months later. The sequence matters more than any single material. None of that shows in a picture, which is why we mark the micron and the cure day on the sheet. Buyers who settle it before an order pay nothing extra, and buyers who settle it after delivery pay a repaint.
A 14 day lead covers 2 days cutting, 2 sanding, 3 paint, 5 curing and 2 assembly, and 5 curing days are 36 percent of the schedule. shop fixtures. The same rule holds for a Shenzhen workshop and a Dubai one, with the booth temperature mattering in both. We keep the alternative on the same sheet, so the buyer compares a coat instead of a render.
Eighteen millimetre MDF
A painted display uses 18 mm MDF on a load bearing side and 12 mm on a back panel, and 18 mm holds a 40 kg shelf without a batten. A 12 mm side panel bows 4 mm across 900 mm. That number belongs on the order sheet, because a micron figure agreed verbally rarely survives a first delivery.
An 18 mm E1 board costs 26 dollars a sheet and a 12 mm 17, and 24 sheets of 18 mm is 624 against 408. Two hundred and sixteen dollars buys 9 mm of stiffness that stops retail displays. Most of these failures appear 6 months after delivery, which is exactly when a cheap coat starts to show.

Three grits, not one
Sanding runs 120 grit, then 180, then 240, and 3 grits remove a 0.4 mm mill mark that 120 alone leaves. A 240 finish holds 40 microns of primer without a visible edge. Mark it on the sheet too, so whoever inspects the next batch has the reference without guessing. One factory visit settles the question faster than a week of sample browsing.
Three grits add 40 minutes per panel and one grit leaves a mark that costs a repaint at 96 dollars. Forty minutes is 0.6 of an hour and a repaint is 4 hours, so 3 grits win glass showcases. None of that shows in a picture, which is why we mark the micron and the cure day on the sheet.
Four numbers on the sheet
The table is the sheet we use on painted display production, and each line answers a micron, a grit or a day rather than a workshop story. Buyers who settle it before an order pay nothing extra, and buyers who settle it after delivery pay a repaint. The same rule holds for a Shenzhen workshop and a Dubai one, with the booth temperature mattering in both.
| Step | Spec |
|---|---|
| Board | 18 mm E1 MDF |
| Sanding | 120 / 180 / 240 |
| Primer | 40 microns |
| Top coat | 2 x 45 microns |
| Curing | 5 days |
Booth at 25 C and 55 percent
A paint booth at 25 C and 55 percent humidity gives a 45 micron coat 20 minutes of dust free time, and at 32 C the same coat skins in 8 minutes with visible lap marks. Temperature is a spec, not a preference. We keep the alternative on the same sheet, so the buyer compares a coat instead of a render.
A booth with 0.3 m per second of downdraft costs 24,000 dollars and a room spray 6,000, and 18,000 buys a dust free surface. An 18,000 booth pays back at 6 rejected units of 300 dollars per month cash counters. That number belongs on the order sheet, because a micron figure agreed verbally rarely survives a first delivery.

Two top coats at 45 microns
A painted display takes one primer at 40 microns and 2 top coats at 45 each, and 130 microns total blocks an MDF edge from moisture for 3 years. A single 60 micron coat lets an edge swell 0.2 mm in 8 months. Most of these failures appear 6 months after delivery, which is exactly when a cheap coat starts to show.
A second coat costs 18 dollars per sqm of panel and a re-paint of a swollen edge costs 120, and a 3 sqm unit is 54 against 120. Two coats are cheaper because swelling is a rebuild, display cases. Mark it on the sheet too, so whoever inspects the next batch has the reference without guessing. One factory visit settles the question faster than a week of sample browsing.

Five days of curing
A 2 part polyurethane cures in 24 hours to touch and 5 days to full hardness, and a display packed at 24 hours takes a 9H print from a strap. Five days is the difference between a finish and a mark. None of that shows in a picture, which is why we mark the micron and the cure day on the sheet.
A 5 day cure adds 4 days over a 1 day schedule on a 20 unit order, which is 80 unit days of storage at 1.5 dollars. One hundred and twenty dollars of storage beats a 2,400 dollar repaint jewellery display cases. Buyers who settle it before an order pay nothing extra, and buyers who settle it after delivery pay a repaint.
Ninety gloss units, cross hatch 1
A gloss display is measured at 85 to 90 gloss units at 60 degrees, and adhesion is tested by a cross hatch at 1 mm spacing with a 1 rating. A 2 rating fails a 6 month outdoor test. The same rule holds for a Shenzhen workshop and a Dubai one, with the booth temperature mattering in both. We keep the alternative on the same sheet, so the buyer compares a coat instead of a render.
A gloss meter costs 380 dollars and a cross hatch kit 60, and 440 buys a number a buyer can audit. Four hundred and forty is 0.3 percent of a 140,000 order and stops kiosk design. That number belongs on the order sheet, because a micron figure agreed verbally rarely survives a first delivery. Most of these failures appear 6 months after delivery, which is exactly when a cheap coat starts to show.

Conclusion
Nine steps, 18 mm board, 3 grits, 130 microns and 5 days. Five numbers cosmetic kiosk. Mark it on the sheet too, so whoever inspects the next batch has the reference without guessing. One factory visit settles the question faster than a week of sample browsing. None of that shows in a picture, which is why we mark the micron and the cure day on the sheet.
Never cut the 5 day cure or the third grit. Cure time is the cheapest insurance on a 20 unit order and a 240 grit is the only way a 45 micron coat reads flat. Buyers who settle it before an order pay nothing extra, and buyers who settle it after delivery pay a repaint. The same rule holds for a Shenzhen workshop and a Dubai one, with the booth temperature mattering in both.
Check a coat at 130 microns and a cure at 5 days. One hundred and thirty microns seals an MDF edge and 5 days gives a 9H surface that a strap cannot print. We keep the alternative on the same sheet, so the buyer compares a coat instead of a render. That number belongs on the order sheet, because a micron figure agreed verbally rarely survives a first delivery.
