UniqueKiosk · Shenzhen workshop

Triple Pocket Acrylic Wall Brochure Rack

$125.00

Clear acrylic wall rack with three staggered pockets and two hanging holes, 300 mm wide and 350 mm tall. Price range: USD 125-210, set by pocket count and width.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Staggered Pocket Set

Three pockets stagger across this brochure holder, so a reader sees each lip from one spot. The top pocket sits level with the panel, and the lower pockets step out and down. Each pocket takes a sheet of up to 148 x 210 mm. A lower notch in every lip leaves a thumb gap. Side walls tie the pockets into one body. The rack runs 300 mm wide and 350 mm tall. This brochure holder carries three titles in a wall spot of one sheet width.

three tier wall brochure rack

Wall Mount Depth

Two round holes at the top panel hold this brochure holder on a wall. The holes sit 120 mm apart, so one plaster anchor and one screw carry the load. A back panel runs flat against the wall, and the pocket depth adds only 60 mm. A clerk hangs the unit with two screws in under five minutes. A framed wall, a slatwall panel and a plaster column all take it. This brochure holder keeps a walkway clear of a floor stand.

brochure rack front view

Sheet And Edge Work

Clear acrylic of 3 mm builds the pockets of this brochure holder. Each pocket bends from a single sheet, so the lip has no weld. A flame polish clears the cut edge, which keeps a printed cover sharp. A solvent joint ties the side walls to the pocket set. The unit weighs about 1 kg empty. A damp cloth clears a mark without a solvent. Our acrylic displays use the same sheet grade.

brochure rack side view

Print On Panel

The top panel of this brochure holder takes a printed heading. We print on the reverse face, so the front stays clear and the text reads through. A logo sits above the top pocket, where a reader looks first. A colour band along the lower pocket lip marks a department. A short campaign takes a vinyl label over the panel. This brochure holder ships plain clear as standard. A retail sign holder takes a second heading.

hanging holes detail

Showroom Placement

A wall rack suits a showroom column, a clinic corridor and a hotel lift lobby. Three pockets hold a price list, a floor map and a service note. A wall spot leaves the counter free for a till or a card reader. A shopper reads the set without a stop in the walkway. Staff pull the whole unit down for a clean in a season. Our wall mounted brochure holders cover a single pocket. A wall mount fixture carries the anchor.

Price And Custom Build

List price starts at USD 125 for this three pocket brochure holder in clear acrylic. A five pocket version at 420 mm width lands near USD 185. A wall brochure rack puts three titles in one narrow wall column. A staggered lip shows every cover from one standing spot. A 3 mm sheet keeps the unit light for a plaster anchor. This brochure holder pairs with literature displays and retail displays fixtures. ukiosks builds this brochure holder to order in Shenzhen. We can reset pocket count, width, hole spacing and print layout. Send your wall plan and we return drawings and a quote.

Specification Detail
Pockets Three staggered pockets
Sheet size Up to 148 x 210 mm
Overall size 300 x 60 x 350 mm
Material 3 mm cast acrylic, clear
Fixing Two 6 mm holes, 120 mm apart
Edge finish Flame polished
Weight About 1 kg

Reviews

There are no reviews yet.

Be the first to review “Triple Pocket Acrylic Wall Brochure Rack”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop