UniqueKiosk · Shenzhen workshop

Crystal Acrylic Tabletop Sign Frame With Stand

$150.00

Tabletop sign frame in thick crystal acrylic with a clear border and a low metal stand, for an A5 sheet at 148 x 210 mm. Price range: USD 100-200, set by size and stand type.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Thick Acrylic Block

A clear block reads like glass with half the weight. This sign frame is built from two 5 mm acrylic sheets with a 10 mm border gap. The inner sheet carries the print, and the outer sheet clamps it. Four screw caps hold the pair together at the corners. The border gives the print a clean white edge. At A5 size it measures 148 x 210 mm and weighs 800 g. A shopper sees the sheet through the border with no frame line. The countertop cases range adds a matching lit panel.

crystal acrylic tabletop sign frame

Low Metal Stand

A low metal stand sets this sign frame at a reading angle. Two stainless tubes run from the bottom screws to a flat foot. The angle is 15 degrees, so a seated shopper reads the whole sheet. The foot is 90 mm deep and sits flat on a counter. A sign frame on a stand takes less space than a printed card holder. Tubes can be swapped for a longer pair to raise the sheet. The stand comes off for a flat lay fix, which retail display fixtures crews often ask for. Every sign frame we ship gets a tilt test.

sign frame front view

Print Insert

Inserting a sheet into this sign frame takes under a minute. Staff lift the outer sheet and slide the print over the inner one. Two corner screws stay in place, and two come out for the swap. A standard paper sheet needs no backing. A thicker card up to 1.5 mm also fits the gap. A border of 10 mm is left clear, so a full bleed print reads clean. The acrylic wipes down with a soft cloth. display cases counters keep one spare print.

sign frame side view

Build And Packing

Acrylic for this sign frame is cut on a laser and flame polished at the edge. The polish removes the saw line, so the border reads clear. Screws are stainless with a domed cap. The stand tubes are cut, deburred and fixed with a thread insert. Each sign frame is squared on a bench before packing. A protective film covers both faces until install. Packing is one carton with a foam sleeve. cash counter desks take a pack of four.

corner screw and stand detail

Counter Uses

This sign frame suits a price card, a tasting note and a small brand board. At A5 it fits a bakery case top or a hotel room desk. A 15 degree tilt keeps a seated reader from leaning in. The clear border does not hide the message behind a dark moulding. A stand foot stays put on a stone or glass top. The frame can switch from portrait to landscape by moving the tubes. Many shop fit outs use one per display shelf. food and drink shops desks use two.

Price And Custom Build

List price starts at USD 150 for this A5 unit. A set of four lands near USD 480 with one print run. A sign frame keeps a price card clean and upright on a busy counter. A thick acrylic border needs no moulding or paint. A low stand reads well for a seated customer. ukiosks builds this sign frame to order in Shenzhen. We can reset sheet size, border width, stand height and screw finish. Send your plan and we return drawings and a quote.

Specification Detail
Sheet size A5, 148 x 210 mm (custom A6-A4)
Acrylic Two 5 mm clear sheets
Border 10 mm clear edge gap
Fix Four stainless screw caps
Stand Stainless tubes at 15 degrees
Weight About 800 g
Packing One carton with foam sleeve

Reviews

There are no reviews yet.

Be the first to review “Crystal Acrylic Tabletop Sign Frame With Stand”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop