UniqueKiosk · Shenzhen workshop

Square Glass Tower Display Case with LED Lights, 400 mm

$1,150.00

A four-sided glass tower display case with LED corner strips, four shelves and a lock. Price range: USD 700-1,500, set by height and lighting.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Glass on Four Sides

This tower display case shows stock from any angle in the room. Glass runs on all four sides, framed by a slim black post at each corner. Four shelves sit inside, spaced 380 mm apart. The case stands 1800 mm tall on a 400 mm square footprint. A shopper walking past sees the top shelf first, then the rows below. A tower display case suits a corner slot or the end of a counter run. Two of them frame an entrance without blocking the walk.

Black Frame and Glass

Posts are 25 x 25 mm steel with a matte black powder coat. Glass is 6 mm tempered on the sides and 8 mm on the shelves. Shelves sit on pin supports and lift out for cleaning. The top cap is folded steel with a black finish. A plinth 120 mm high lifts the glass off the floor. Each shelf holds 12 kg, so a tower display case carries about 48 kg of stock in total. The 1800 mm height keeps the top shelf in view.

LED Strips and Lock

Four vertical LED strips run down the corners, one per post. Output is 12 W in total and the colour sits near 4000 K. A switch sits on the plinth, out of the display line. One hinged glass door opens on the front face and closes on a cam lock. Cable entry is at the base, so no wire shows up the frame. A tower display case with corner light reads even from the back. Light does not sit on the glass face, so glare stays low.

Specification Detail
Dimensions 400 x 400 x 1800 mm
Frame 25 x 25 mm steel, matte black
Glass 6 mm sides, 8 mm shelves
Shelves 4, 380 mm spacing
Lighting 4 LED strips, 12 W total
Weight 52 kg empty
Lock cam lock on glass door

Where It Sits

Use one beside a till, or two flanking a doorway. The square base fits a 500 mm gap with no overhang. Keep 600 mm clear in front of the door for loading. Place the case away from direct sun, since the glass will hold heat. A tower display case near a door needs a rubber sweep at the base. A tower display case works well for watches, small ceramics and boxed pens. Compare display cases for wide bays or jewelry displays for tray layouts.

Delivery and Setup

The case ships in one crate with the shelves packed separately. Two people set it up in about 30 minutes. Fit the plinth first, then the frame, then the glass. Shelves drop onto pins without tools. Weight is 52 kg empty, so two people move a tower display case with a trolley. Wire the lights to a 12 V driver in the plinth. store operations teams wipe the glass each morning and check the lock. store display planning covers island layouts built on the same base.

Cost and Custom Build

One narrow footprint gives four selling levels with no wall space used. Corner light lifts small stock without glare on the glass. Shelves lift out, so a full reset takes minutes. The lock covers a whole day of trading. List price starts at USD 1,150 for the 1800 mm case. Ukiosks builds this tower display case in any height, shelf count and frame colour. Our team quotes from a drawing. Browse countertop displays for bench units, or send sizes through our contact page.

Reviews

There are no reviews yet.

Be the first to review “Square Glass Tower Display Case with LED Lights, 400 mm”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop