UniqueKiosk · Shenzhen workshop

Isla Oak Twelve Pocket Floor Magazine Rack, 1350 mm

$380.00

Floor magazine rack in light oak with twelve slanted pockets on two legs. Price range: USD 380-760, set by pocket count and wood finish.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Pocket Layout

This magazine rack carries twelve pockets in two columns and six rows. A magazine rack with a 210 mm pocket takes an A4 title and a folded leaflet. Each pocket slants back at 20 degrees, so a cover reads at a glance. The front lip sits at 25 mm, so a title stays in place. A pocket holds a stack of three copies. The frame runs 1350 mm tall, so the top row sits near eye level. A brochure holder takes the same pocket.

Oak Frame

The frame is light oak with a clear matte seal. A magazine rack in this wood shows a clean grain on the side panel. The board runs 18 mm thick on the pocket and 25 mm on the leg. The wood is kiln dried, so a panel does not move in a dry room. The seal keeps a coffee ring off the face. A shop wipes the frame with a dry cloth.

Legs and Load

Two side legs take the frame of this magazine rack. A magazine rack on a T base stands stable on a tile floor. Each leg ends in a flat foot at 300 mm, so no rock shows on a small dip. Four pads sit under the feet, so a wood floor takes no mark. The frame holds a full set of magazines with no tilt. A staff member moves the unit on its feet with a light lift. Our wooden rack shares this leg.

Specification Detail
Pockets Twelve
Height 1350 mm
Pocket Size 210 mm
Wood Light oak, 18 mm
Slant 20 degrees
Base T foot, 300 mm
Weight 14 kg

Lobby and Store

A clinic sets this magazine rack in a waiting area beside a chair row. A hotel uses one at a lobby for a city guide. A showroom uses one for a catalogue line. A library puts one near a reading table. Literature racks of this build pair with a side table. A room with a low window likes the 1350 mm frame, since the top row still clears the sill. A display stand sits beside it.

Build Notes

The pockets are cut on a saw with a stop, so twelve match in width. A magazine rack of this build keeps an even row after a season. The pocket joints are glued and pinned, then sanded at the face. The frame gets two coats of clear seal with a light sand between. Each unit is checked for a square frame and a firm foot before packing. Read our bench notes for the joint detail.

Sizes and Price

Pocket count runs at twelve, fourteen or twenty for this magazine rack. Height runs at 1350, 1500 or 1800 mm. The wood comes in light oak, walnut or a white paint. The pocket comes in wood or clear acrylic. A header panel, a floor anchor and a carry carton are options. List price starts at USD 380 for the twelve pocket unit. ukiosks builds this magazine rack in Shenzhen to order, so send your drawing through contact us.

Reviews

There are no reviews yet.

Be the first to review “Isla Oak Twelve Pocket Floor Magazine Rack, 1350 mm”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop