UniqueKiosk · Shenzhen workshop

Amber Black Wooden Barber Station with Mirror and Basin, 1200 mm

$1,180.00

Barber station in black wood with gold trim, a wide mirror, a basin and closed storage below. Price range: USD 1180-2600, set by width and basin set.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Station Form

This barber station runs 1200 mm wide and 1950 mm tall. A barber station of this size gives one cutting place on a shop floor. A wide mirror sits over the counter, so a client sees the cut in progress. A basin sits at the centre, so a wash runs at the chair. Side shelves hold bottles, so a tool stays within reach. One station serves one stylist. A retail display plan sets the wall run.

Wood and Trim

The body builds from 18 mm plywood with a black wood veneer face. A barber station in this build holds a basin splash with no swell. Gold anodised trim frames the mirror and the lower panel, so a unit reads warm. The counter top runs a solid white stone sheet, so a wet towel leaves no mark. Doors close on soft hinges, so a store room stays quiet. A damp cloth keeps the veneer clean.

Shop Set

A barber station of this build sets in about ninety minutes. Two staff lift the upper cabinet, then level the base. A mirror mounts on a steel bracket, so a panel stays flat. The basin drains to one waste pipe, so a plumber works at one point. Doors and shelves adjust on a pin, so a layout changes later. A shop of 40 sqm fits four stations at this width. Our countertop display crew checks the level.

Specification Detail
Width 1200 mm
Height 1950 mm
Board 18 mm ply
Veneer Black wood
Counter Stone sheet
Basin Central bowl
Doors Soft close

Shop Use

A barber shop uses this station for a classic cut bay. A salon uses one for a colour bar. A hotel uses one for a grooming room. A training school uses one for a demo bench. Store fixtures of this build fill a service wall. A wall of 6 m takes three stations at this width. A wood display bay joins the service wall.

Build Notes

The board cuts on a panel saw, then edges on a bander. A barber station of this build keeps a flat face after a year. The veneer presses on a glue line, so a panel reads even. The mirror sets on a safety backing, so a break runs safe. Each lot is checked for a level counter and a sealed drain before packing. Read our bench notes for the drain test. A barber station of this build ships flat packed.

Sizes and Price

Width runs at 1000, 1200 or 1500 mm for this barber station. Height runs at 1900 or 2100 mm. The veneer comes black, walnut or oak. A basin, a towel warmer and a LED mirror set are options. List price starts at USD 1180 for the 1.2 m station. ukiosks builds this barber station in Shenzhen to order, so send your drawing through contact us.

Reviews

There are no reviews yet.

Be the first to review “Amber Black Wooden Barber Station with Mirror and Basin, 1200 mm”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop