UniqueKiosk · Shenzhen workshop

Ink Grey Velvet Jewelry Counter Riser, 400 mm

$75.00

Jewelry riser in grey velvet with three stepped tiers and slotted ring rows. Price range: USD 75-180, set by tier count and size.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Steps and Slots

This jewelry riser runs 400 mm wide and 250 mm deep. A jewelry riser of this size lifts three rows into view inside a counter. The steps rise at 40 mm, so a back row reads over a front row. Each lower step carries 20 ring slots, so a tray shows a full size run. The top step stays flat for a pendant or a watch. The velvet face holds a ring in place. A retail display plan sets the tray zone.

Velvet Build

The body is a grey board box with a foam core. A jewelry riser in this build keeps a soft face after daily use. The velvet bonds to the foam with a spray glue, so a corner shows no seam. The slots cut on a die, so a row stays even. The base carries a felt pad, so a riser slides without a scratch on glass. A soft brush clears a dust line from the velvet.

Counter Setup

A jewelry riser of this size sets in a counter in one minute. A staff lifts the lid, then lays the riser on a mat. The steps face the shopper, so a hand reaches the front row first. Two risers stack side by side, so a 900 mm counter holds a full run. A riser fits a tray of 450 mm. A velvet brush keeps the face clean through a day. Our store fixture crew packs this tray.

Specification Detail
Width 400 mm
Depth 250 mm
Tiers 3
Step rise 40 mm
Ring slots 40
Face Grey velvet
Base Felt pad

Store Use

A jeweler uses this jewelry riser for a ring line. A boutique uses one for earrings. A watch shop uses one for bands. A trade show uses one for a show tray. Jewelry displays of this build pair with a bust. A counter of 900 mm takes two risers at this width. A glass lid keeps dust off a full tray. A countertop display holds the full line.

Build Notes

The board cuts on a beam saw, so a step meets square. A jewelry riser of this build keeps a level row after a season. The foam block shapes on a hot wire, so a step reads clean. The velvet runs through a laminator, so a face holds flat. Each lot is checked for an even slot row and a smooth face before packing. Read our bench notes for the slot check.

Sizes and Price

Width runs at 300, 400 or 500 mm for this jewelry riser. Tiers run at two, three or four. The velvet comes grey, black or cream. The slot row comes for rings, earrings or bangles. A lid, a tray base and a brush are options. List price starts at USD 75 for the 400 mm riser. ukiosks builds this jewelry riser in Shenzhen to order, so send your drawing through contact us.

Reviews

There are no reviews yet.

Be the first to review “Ink Grey Velvet Jewelry Counter Riser, 400 mm”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop