UniqueKiosk · Shenzhen workshop

Cobalt Single Bar Clothing Rack with Oak Plinth Base

$295.00

Single bar clothing rack on a white T pole with an oak plinth base. Price range: USD 295-480, set by pole height and finish.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Pole and Rail

This single bar clothing rack uses one upright pole and one short top rail. The pole runs 50 mm thick from the base to the rail at 1500 mm. A shop hangs four or five pieces and the rail reads balanced on one side. A single bar clothing rack of this shape keeps a corner open without a frame. The rail carries 25 kg and takes standard hanger hooks. Both rail ends are capped, so a hanger stops at the tip. Single bar clothing racks list this pole size.

Oak Base

An oak plinth base holds this single bar clothing rack steady on a flat floor. The base runs 600 mm long and 350 mm wide with a 30 mm thickness. Weight sits low, so a loaded rail does not tip. Four feet sit under the base and keep the wood off a wet floor. A shop can also place a basket or a shoe pair on the plinth. A single bar clothing rack with a wood base reads warmer than a steel foot. Wooden racks use this base thickness.

Build Details

The pole is steel tube with a white powder coat at 60 microns. A machined flange joins the pole to the base and takes four bolts from below. The rail sits on a T joint with a welded insert, so the joint holds under load. A single bar clothing rack of this build stays upright within 1 mm on a level floor. The oak base carries a matte clear seal against hand marks. Each unit leaves the bench after a tip test with 25 kg on one rail end.

Specification Detail
Rail Width 600 mm
Height 1500 mm
Pole 50 mm steel tube
Base Oak plinth 600 x 350 mm
Finish White powder coat, matte seal
Load 25 kg on the rail
Feet 4 levelling glides

Shop Use

Boutiques use this single bar clothing rack for a feature look near the door. A stylist sets one outfit on the rail and a pair of shoes on the base. A tailoring shop keeps a jacket and trousers at the fitting area. A hotel shop uses the rack for a single capsule line. Retail clothing racks pair with this rail height. A shop with a small floor likes the footprint, since the base takes under a square metre. Read our bench notes for the build detail.

Finish Options

The pole comes in white, black or brushed brass. The base comes in natural oak, walnut stain or a painted matte. A brass coat on the pole lifts the look in a luxury room. A matte black pole reads better against a pale wall. A single bar clothing rack with a painted base suits a pop up stand. The finish is applied after the weld and the sand, so no seam shows through the coat. A dual pole version shares the double rail layout.

Sizes and Price

Rail width runs at 600 mm, 800 mm or 1000 mm. Pole height runs at 1400 mm or 1500 mm. Base size runs at 600 x 350 mm or 700 x 400 mm for this single bar clothing rack. A hook kit and a base mat are options. A shop can also order a twin pole version for two rails. List price starts at USD 295 for the 600 mm unit. ukiosks builds this single bar clothing rack in Shenzhen to order, so send your drawing through contact us.

Reviews

There are no reviews yet.

Be the first to review “Cobalt Single Bar Clothing Rack with Oak Plinth Base”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop