UniqueKiosk · Shenzhen workshop

Concord Walnut Jewellery Counter with Brass Hood

$1,450.00

Walnut jewellery counter with a brass framed glass hood, white deck and six drawers. Price range: USD 1,450-2,150, set by length.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Counter Form

This jewellery counter runs 1500 mm long and 600 mm deep at a 950 mm working height. A brass frame sits on the deck and carries a clear glass hood. Six drawers fill the body in two columns of three. A shop keeps the deck for trays and the drawers for stock. A jewellery counter at this height lets a customer lean and look down into the case. The brass frame runs 15 mm square on every edge. Jewellery displays list this length.

Drawer Layout

Six drawers sit under the deck of this jewellery counter. Each drawer runs 720 mm wide and 420 mm deep with a felt insert option. A brass pull runs the full width and takes a soft close slide. The drawer fronts carry walnut veneer with a vertical grain. A shop stores ring trays in one column and boxed stock in the other. A central lock bar takes one key for the block. Display cases share this drawer depth.

Brass and Glass

The hood frame uses solid brass tube with a satin clear coat. Clear glass runs on all four sides at 6 mm. A shop opens the hood from the top for a fast reset. The glass sits in a brass channel and no silicone line shows. A jewellery counter with a brass frame reads warm next to walnut. The deck under the hood is a white laminate, so a diamond reads bright. Countertop displays use this deck build.

Build and Finish

The body is 18 mm plywood with a walnut veneer and a hand rubbed lacquer. Brass parts are machined and clear coated, then buffed by hand. The plinth sits 30 mm off the floor with a brass skirt. Joints are glued, screwed and clamped, then sanded level. A jewellery counter of this build carries 90 kg on the deck. Each unit leaves the bench after a check on the drawer line. A drawer that sits proud of the frame is pulled and reset before packing. Read more on our factory bench.

Shop Fit

A jeweller sets this jewellery counter at the entrance and puts a low case behind it. A watch dealer runs two units back to back and shares the brass line. A bridal shop uses one for rings and keeps the veils on a rail nearby. A museum shop sets a single piece under the hood and the case reads like a plinth. Store fixtures pair with this counter height. A shop with low light likes the white deck, since it lifts the piece.

Order and Price

Length runs at 1200 mm, 1500 mm or 1800 mm. The hood height runs at 250 mm or 350 mm. Drawer count runs from four to eight for this jewellery counter. The frame comes in brass, bronze or brushed steel. The veneer comes in walnut, oak or a dark stained ash. A felt insert, a light strip and a sliding hood are options. List price starts at USD 1,450 for the 1500 mm unit. ukiosks builds this jewellery counter in Shenzhen to order, so send your spec through contact us.

Specification Detail
Length 1500 mm
Depth 600 mm
Height 950 mm
Drawers 6 in two columns
Hood Frame 15 mm solid brass
Deck White laminate
Load 90 kg on the deck

Reviews

There are no reviews yet.

Be the first to review “Concord Walnut Jewellery Counter with Brass Hood”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop