UniqueKiosk · Shenzhen workshop

Tiered Clear Acrylic Brochure Holder

$55.00

Clear acrylic brochure holder with two stacked pockets in one third A4 size, 99 mm wide and 210 mm tall. Price range: USD 55-90, set by pocket count and print.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Two Pocket Build

Two pockets stack in one body on this brochure holder. The lower pocket takes a leaflet and the upper pocket takes a thin booklet. A tall back panel rises above the top pocket as a header. Each lip runs a wide notch, so a thumb pulls a sheet clear. The unit measures 99 mm wide and 210 mm tall. Depth runs 105 mm at the base. This brochure holder fits a narrow counter gap. Our literature displays carry the same format.

tiered acrylic brochure holder

Acrylic Sheet Grade

Cast acrylic sheet of 3 mm forms each panel of this brochure holder. Edges are polished by flame, so the rim reads clear, not milky. Panels bond with a solvent cement joint, which leaves a thin visible line. A clear sheet passes light through the pocket, so a printed cover reads full. The material resists a wipe with a wet cloth. A cast sheet takes a light load without a stress mark. This brochure holder keeps its clarity over years of front desk use.

brochure holder front view

Counter Placement

This brochure holder sits flat on a counter with its wide base. A 105 mm footprint leaves room for a card terminal or a till. The slant face puts the leaflet at a reading angle of about 30 degrees. A shopper can pull a sheet without a reach across the desk. The unit weighs about 400 g, so a clerk moves it in one hand. Clear acrylic shows the counter finish under it. Our acrylic displays use the same base pattern.

brochure holder side view

Print Options

A logo or a headline can print on the back panel of this brochure holder. We print on the reverse side, so the front face stays clear. A single colour screen print suits a small run. A full colour label sits behind the panel for short campaigns. The pocket front can carry a size note in small type. Print sits above the top lip, where a shopper reads it first. This brochure holder ships with a plain clear panel as standard.

pocket lip detail

Front Desk Use

A front desk, a clinic and a hotel lobby suit this brochure holder. A two pocket layout splits a price list from a leaflet. The small width fits between a card reader and a screen. Staff swap the printed sheet in under a minute. A clear body keeps the counter look light and open. A spare pocket set covers a second language. Our wall mounted brochure holders cover a wall version. A retail sign holder reads beside it.

Price And Custom Build

List price starts at USD 55 for this two pocket brochure holder in clear acrylic. A three pocket version with a printed header lands near USD 78. A tiered brochure holder puts two leaflets in one small footprint. A polished edge lifts the look of a plain counter. A cast sheet holds clarity through daily use. This brochure holder pairs with countertop displays and retail displays fixtures. ukiosks builds this brochure holder to order in Shenzhen. We can reset pocket size, tier count, sheet thickness and print layout. Send your leaflet size and we return drawings and a quote.

Specification Detail
Pocket count Two stacked pockets
Sheet size 99 x 210 mm, one third A4
Overall size 99 x 105 x 210 mm
Material 3 mm cast acrylic, clear
Edge finish Flame polished
Base Flat wide base, 105 mm deep
Weight About 400 g

Reviews

There are no reviews yet.

Be the first to review “Tiered Clear Acrylic Brochure Holder”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop