UniqueKiosk · Shenzhen workshop

Two Tier Wooden Countertop Display Case

$360.00

Wood framed countertop display case with a glazed top, one glass shelf and a two panel front, 460 x 250 x 320 mm. Price range: USD 300-600, set by size and timber.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Wood Frame Case

A wood frame holds this countertop display case together. The case is 460 mm wide, 250 mm deep and 320 mm tall. Rails are 22 mm thick walnut with a mitered corner at each end. Glass panels sit in a 6 mm rebate, so no edge shows outside the timber. The front is split by a 30 mm wood mullion, which gives two panes. The top is glazed too, so light reaches the deck. The countertop cases range adds a 600 mm version.

two tier wooden countertop case

One Shelf, Two Levels

One glass shelf splits this countertop display case into two levels. The shelf is 6 mm with a polished edge and rests on four small wood cleats. Clearance runs 120 mm above and 140 mm below, so a boxed item fits either level. The deck is bare walnut, so a felt pad sits flat. There is no lock on this model. Every countertop display case we build gets a shelf fit check. display cases cases use the same cleat.

wooden case front view

Mitered Joints

Mitered joints give this countertop display case a clean corner. Each rail meets at 45 degrees with a glued spline, then sanded flush. No pin or screw shows on the outside face. The top cap sits over the side rails, so water on a counter does not enter the glass rebate. A matte clear coat keeps the walnut tone even. Staff wipe the frame with a damp cloth, then a dry one. retail display fixtures crews check each joint on arrival.

wooden case side view

Build and Packing

Panels for this countertop display case are cut, rebated and assembled in one bench run. Glass is cut to the rebate size and packed in a sleeve. The whole case is squared, then the shelf cleats are set at the chosen heights. Every countertop display case is checked for a level deck before packing. Packing is one carton with foam corners and a timber corner guard. cash counter counters often order three for a run.

mitered corner joint detail

Where It Fits

This countertop display case suits a tea shop, a pen counter and a small antique stall. A 460 mm footprint fits a narrow table with a card reader beside it. Height at 320 mm keeps the goods low, so a shopper looks down into both levels. The wood frame ties to timber shelving behind the counter. Two panes give staff a quick view of the whole stock. The shop fit outs package adds a card stand. food and drink shops counters use two.

Price and Custom Build

A wood frame reads warm on a timber counter and hides the glass edge. Two panes with a mullion give the case a steady look. One shelf doubles the selling area in the same footprint. List price starts at USD 360 for the 460 mm unit. A 600 mm build with two shelves lands near USD 490. ukiosks builds this countertop display case to order in Shenzhen. We can reset width, timber tone, shelf count and mullion width. Send your plan and we return drawings and a quote.

Specification Detail
Overall size 460 x 250 x 320 mm (custom 350-600 mm)
Material 6 mm glass in 22 mm walnut frame
Shelves One glass shelf on wood cleats
Top Glazed top panel
Front Two panes split by 30 mm mullion
Finish Matte clear coat
Packing One carton, about 10 kg

Reviews

There are no reviews yet.

Be the first to review “Two Tier Wooden Countertop Display Case”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop