UniqueKiosk · Shenzhen workshop

Mahogany Countertop Glass Showcase With Lock

$340.00

Countertop display case with a clear glass box on a mahogany base, a key lock and a glass top, 450 x 300 x 250 mm. Price range: USD 300-600, set by size and timber finish.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Low Glass Box

A low glass box gives a wide flat stage on a counter. This countertop display case is 450 mm wide, 300 mm deep and 250 mm tall. Glass is 6 mm clear float with a polished edge, held by a sealed joint at each corner. The top panel sits on the sides, so nothing blocks the view from above. The interior is one open deck with no shelf. Weight runs near 8 kg, so a staff member shifts it alone. The countertop cases range adds a 600 mm wide unit.

mahogany countertop glass showcase

Mahogany Base

A mahogany base carries this countertop display case. The block is 70 mm tall, faced in a dark red veneer with a soft sheen. It sits on four small pads, so the base does not scratch a counter. A 12 mm recess holds the glass, so the panel sits below the wood edge. The lock is set in the front face, level with the deck. Every countertop display case we build gets a base seal before packing. display cases cases use the same profile.

showcase front view

Lock and Opening

This countertop display case locks through the base, not the glass. A cam lock turns into a rail under the deck and holds the front panel shut. One key ships with each unit, and a second key is an option. To restock, a staff member unlocks the front and lifts the glass box off. The whole box comes away as one piece, so the deck is clear. No hinge means fewer parts to wear. Many retail display fixtures crews like that on site. This countertop display case ships with clear fitting notes.

showcase side view

Build and Finish

Glass for this countertop display case is cut and polished in one set. Panels are checked for square before the joint cement goes on. The base is board with a veneer face, edged and sealed at the corners. A matte clear coat keeps the red tone even under shop light. Packing is one carton with foam corners and a card between panels. cash counter counters often pair two units for a 900 mm run.

mahogany base corner detail

Where It Works

This countertop display case suits a medal collection, a watch tray and a small museum table. A 450 mm footprint fits a narrow counter with a till beside it. Height at 250 mm keeps the deck inside a seated shopper sight line. The glass top lets overhead light reach the goods with no shadow. Two units side by side read as one long case. The shop fit outs package adds a card stand. food and drink shops tills keep one for small stock.

Price and Custom Build

A flat glass top lets a shopper look straight down at the goods. A mahogany base gives the case weight and a warm tone. A single cam lock covers the stock without a hinge line. List price starts at USD 340 for the 450 mm unit. A 600 mm build with a deeper base lands near USD 470. ukiosks builds this countertop display case to order in Shenzhen. We can reset width, depth, timber tone and glass height. Send your plan and we return drawings and a quote.

Specification Detail
Overall size 450 x 300 x 250 mm (custom 350-600 mm)
Glass 6 mm clear float, polished edge
Base 70 mm mahogany veneer block
Access Lift-off glass box with cam lock
Top Flat glass panel, full view
Weight About 8 kg
Packing One carton with foam corners

Reviews

There are no reviews yet.

Be the first to review “Mahogany Countertop Glass Showcase With Lock”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop