UniqueKiosk · Shenzhen workshop

Umbrella Food Cart in Stainless With Twin Canopies

$3,000.00

Stainless food cart on two umbrellas with a glass display box, open deck and diamond plate front, sized 2.0 x 1.0 m. Price range: USD 2,000-6,600, set by size and deck fit out.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Twin Umbrella Shade

Two umbrellas shade the deck of this food cart. Each canopy is 2.0 m across, in red and yellow panels, held on a 40 mm steel pole. Poles bolt to the deck through socket plates. Open shade covers 4.0 sqm of work area. Canopies fold down for towing and storage. This food cart works in sun without a fixed roof frame. Every food cart we build for open pitches keeps poles clear of the cooking line. The food and drinks lane at a summer fair suits this layout.

stainless umbrella food cart

Deck and Glass Box

An open deck runs 2.0 m across this food cart. The deck is 1.0 mm stainless on a ply core, folded at the edges. A griddle zone sits at the right, 500 mm wide, with a gas ring under it. A glass display box sits at the left, 600 mm wide and 400 mm tall. The box has two shelves and a lift lid. Bread and buns stay covered but in view. Staff work between the box and the plate. This food cart keeps the service line in one run. The counter sits at 900 mm.

food cart front view

Diamond Plate Body

Diamond plate panels face this food cart along the front and sides. Plate is 1.2 mm with a raised pattern, welded to a 25 mm frame. The pattern hides dents from trolleys and corners. A stainless skirt runs at the base, 100 mm high. Two wheels sit under the body with sealed bearings. A draw bar sits at the left for a tow handle. Body weight lands near 160 kg empty. display cases glass can replace the box lid for a full front case.

food cart side view

Build and Finish

Frames are cut and welded on a jig, then squared on a steel table. Plate panels are sheared and welded at the corner posts. Weld seams get a pickle pass before a brush finish. Pole sockets are welded through the deck for load spread. Every food cart is assembled and pushed on a test floor. cash counter counters use the same plate pattern. countertop cases cases fit the deck gap when a shop needs a second display.

diamond plate and deck

Setup and Use

Setup takes one person about 20 minutes. Push the cart in, open both canopies, lock the poles. Gas runs from a bottle on the side tray. Water is not built in, so a vendor brings a cooler and a tub. The footprint is 2.0 m by 1.0 m with canopies open. Clean down is a scraper for the plate and a cloth for the box. retail display fixtures spacing rules keep a gap at the wheels. This food cart fits a 2.2 m bay.

Price and Custom Build

Two umbrellas cost less than a fixed roof and still shade the whole deck. Diamond plate takes street wear without repainting. A glass box keeps buns clean while they sell. List price starts at USD 3,000 for the 2.0 m build. A single umbrella cart with no box lands near USD 2,200. ukiosks builds this food cart to order in Shenzhen. We can reset deck length, plate zone, box size and canopy colour. Send your plan and we return drawings and a quote. Nearby food and drinks kiosks and coffee fit-outs counters share the same deck frame.

Specification Detail
Overall size 2.0 x 1.0 x 2.3 m (custom 1.6-2.8 m)
Body 1.2 mm diamond plate on 25 mm frame
Umbrellas Two 2.0 m canopies on 40 mm poles
Deck Stainless deck with 500 mm griddle zone
Glass box 600 x 400 mm, two shelves, lift lid
Wheels Two wheels with sealed bearings, draw bar
Packing Two crates, about 160 kg

Reviews

There are no reviews yet.

Be the first to review “Umbrella Food Cart in Stainless With Twin Canopies”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop