Avada Car Dealer News

Two panels, one decision

Every kiosk quote hides the same question. Will the body be MDF or plywood? The answer moves the price by a few percent and the working life of the unit by several years, and it decides how the kiosk behaves on the second fit out rather than the first. Most buyers only ask the question after the deposit is paid, when the cutting list is already signed and the panels are ordered.

Walk a mall floor and both panels are easy to spot. A kiosk with a swollen bottom edge and lifted laminate is usually MDF left unsealed at the cut. A kiosk with a hinge screw that will not tighten is MDF asked to carry a load it was never designed to take. Ten minutes on a trading floor teaches a buyer more than any catalogue page, because every failure is visible at knee height.

kiosk shell

What MDF and plywood actually are

MDF is wood fibre glued and pressed into a flat sheet, so the grain disappears and the panel cuts and routes the same way in every direction. That uniform face is why MDF takes paint without telegraphing a joint line through the film. Thickness stays consistent from sheet to sheet, which keeps door gaps even across a long run of cabinets and counters.

Plywood is thin veneers stacked at right angles and pressed under heat. The crossed layers give it a grain direction, a stiffer span for the same thickness, and a grip on a screw that MDF simply cannot match on its best day. Cost rises with the number of layers, so a five layer board and a seven layer board behave differently under the same shelf load.

Core, face and edge compared

The core sets the strength and the face sets the look. A plywood core with a laminate face is the usual commercial build, because the core carries the load and shop fixtures from trolleys, keys and cleaning cloths. Put the money where the load is and leave the decoration to the panel that faces the customer at eye level.

Edge treatment separates a good cabinet from a cheap one. A taped and trimmed edge on plywood stays flat for years, while a painted MDF edge picks up a visible line as the board moves with the seasons and the air conditioning cycle. On a busy floor the edge takes more knocks than the face, because trolleys and cleaning machines reach the base first.

Screw holding, the deciding test

Hinges and drawer runners are the parts that fail first, and both of them rely on screws. A number ten screw driven into plywood holds roughly sixty percent more pull out load than the same screw driven into MDF of the same thickness. A kiosk that opens fifty times a day will expose any weakness in the fixing long before the finish shows age.

That single number explains most service history. A kiosk with MDF doors needs threaded inserts at every hinge, and a kiosk built to be shipped twice kiosk design and every runner bracket. Threaded inserts cost a few dollars per door and remove the problem entirely, which is why we fit them as standard. In practice that single choice decides the build, the budget and the service call history.

Test it before you place the order. Drive a screw into an offcut, then take it in and out five times. On plywood the thread still bites on the fifth pass, and on MDF the hole is smooth and useless by the third. Bring the offcut to the meeting and let the buyer try it, then the panel choice stops being a matter of opinion.

glass case

Moisture and humidity behaviour

MDF absorbs water at the edge and swells there, and that swell does not reverse when the board dries out. One mop line along a kiosk base is enough to lift the laminate above it and leave a ridge you can feel with a finger. Raise the unit on a sealed plinth and the mop water never reaches the board, which removes the most common failure we see.

Plywood moves as well, but it moves across the panel rather than at the edge, and it comes back closer to its original thickness once the air dries. glass showcases survives a wet mall floor that would ruin an MDF one in a month. Specify a sealed back panel and an expansion gap at the wall, and the movement stays inside the frame instead of bowing outward.

Humidity matters more than standing water. A kiosk shipped from Shenzhen to a Gulf mall lands in air at eighty percent relative humidity, and an unsealed MDF back panel will bow away from the frame within a single trading season. Ask for a moisture content reading on the cutting list, because a panel shipped at the wrong reading will move after installation.

counter face

Cost per bay in 2026

Prices below are factory terms, fob Shenzhen, typical range for 2026. The bay is 1.2 m wide by 2.2 m high, with a laminate face over a steel sub frame and a sealed plinth at the base of every option in the table. Every figure includes the plinth, the steel sub frame and the edge seal, so the comparison is like for like rather than a stripped carcass.

The gap between the two panels is smaller than most buyers assume, and it narrows further once edge sealing, inserts and a second crate are priced into the MDF option at the quotation stage. Add inserts, edge sealing and the second crate for a rebuildable unit, and the two options land within ten percent of each other.

Freight changes the maths again. Plywood is denser per square metre of usable panel, so a full kiosk in crates weighs more and counters and towers built in MDF, which matters on air freight. On sea freight the difference is small, but on air freight the heavier crates can add more to the landed cost than the panel itself.

Build Body Price per bay
Entry kiosk MDF, laminate face US$180–260
Standard kiosk Plywood, laminate face US$240–360
Rebuildable kiosk Plywood, inserts at hinges US$300–420
Wet floor kiosk Plywood, sealed plinth US$320–450

Weight, freight and rebuild cost

A three metre kiosk body in MDF weighs roughly one hundred and eighty kilograms before the counter, glass and lighting go in. The same body in plywood lands near two hundred and twenty kilograms, which changes floor loading and volume weight charges. Check the lease before the drawing is signed, because some mall floors cap the load per square metre and the heavier build needs approval.

Rebuild cost runs the other way. A kiosk taken down and re-erected twice a year will strip its MDF screw holes in the first two moves, and every repair after that is a workshop job rather than mall kiosk design. A kiosk that stays in one place for five years never shows the weakness, so the penalty only appears when the unit moves.

Which panel for which kiosk part

Faces and fascias suit MDF, because the panel is painted flat, the shape is routed cleanly, and nothing on a fascia is asked to hold a load or take a hinge. That is where the material saves money without risk. That is where the material saves money without carrying risk, and it is the first place we look when a buyer needs a lower price.

Anything that carries a door, a drawer or a shelf bracket suits plywood. Structural parts such as the plinth, the back frame and display cases in every build we quote, because the saving is tiny and the failure is expensive. Doors, drawers and shelves are the parts that move, and moving parts are where an under specified panel fails first in service.

Mixed builds are normal and rarely a problem. The real mistake is mixing without telling the workshop, because the cutting list then assumes one panel thickness across the whole unit and cosmetic counters. Send the panel per part on the drawing and the workshop will cut it correctly, even when three different boards meet inside one carcass.

shelving bay

Finishing, paint laminate or veneer

Paint flatters MDF. The fibre face is uniform, so a sprayed finish reads flat under a downlight, and a routed edge keeps a crisp radius without needing a separate edge band cut and trimmed by hand. It also hides a repair well, which matters on a branded kiosk where a visible patch would sit right at the customer eyeline.

Laminate flatters plywood, because the face is already stable and the edge can be taped and trimmed to the same colour in one pass. acrylic risers, and it needs a plywood core for the same reason a floor needs a solid sub base. Laminate also resists cleaning chemicals better than paint, which is why food and cosmetics kiosks usually specify it on the working surfaces.

Whichever finish is chosen, seal every cut edge before assembly. An unsealed edge is the entry point for moisture, and moisture is the difference between a kiosk that lasts one lease and one that lasts three. A two dollar seal at the workshop saves a two hundred dollar repair on site, and it is the cheapest insurance in the whole build.

cash wrap

What to specify on a drawing

A panel note belongs on the drawing, not in an email thread. Mark the body panel part by part, mark the edge seal, and mark the insert positions at every hinge, every runner bracket and jewelry cases. A note on the drawing travels with the job, while an email is read once by one person and then lost in the thread.

Ask for the cutting list with the drawing. That list shows the panel per part, and a mismatch between the list and the note is the most common source of a dispute once the crates arrive on site and assembly begins. Check the panel column against the note before production starts, because a mismatch discovered on site stops the installation that day.

Send the floor plan and the product list with the note. Depth and bay width decide the span, and the span decides whether a shelf needs a mid support or a thicker panel to hold retail displays. Depth and bay width also decide the crate size, and the crate size decides what a standard pallet will carry on the shipping line.

tower unit

Conclusion

Plywood for structure, MDF for faces. That single rule covers most kiosk parts, and it keeps the cost close to the MDF option while removing the failures that show up in the second year of trading. Applied to a whole kiosk it also keeps the weight down, because the heavy panel only appears where the load actually is.

Specify the panel per part, seal every edge, and put inserts at the hinges. The rest of the build is detail, and detail is far easier to fix on a drawing than on a mall floor with the store due to open. Do that and the second fit out costs a crate and a crew, rather than a new carcass and a new set of doors.

We cut kiosk panels in Shenzhen to a drawing and quote both options side by side, so the panel choice becomes a line in the budget rather than a guess made after the first delivery lands. Both options arrive on the same drawing, so the buyer compares a real number instead of a verbal estimate from two suppliers.