UniqueKiosk · Shenzhen workshop

Chalk White Guard Booth with Sliding Window, 1200 mm

$7,200.00

A prefabricated guard booth with a sliding window, a steel door and a raised plinth base. Price range: USD 6,200-8,600, set by size and glazing.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

One Person, One Post

A guard booth gives a single officer a dry, lit place to watch a gate. This unit stands 2,400 mm high on a 1,200 mm square base. The raised plinth lifts the floor 150 mm off wet ground. One person works a full shift inside, with a desk at 900 mm. The booth ships as four panels and a roof, so a two-person crew sets it in a day. Site managers order it with a modular kiosk build for gate rows.

Panel Shell and Frame

The walls are 50 mm sandwich panels on a galvanised steel frame. A white steel face wraps a rigid foam core, which holds heat out in summer. The guard booth frame bolts at the corners, and the joints sit behind cover strips. A ribbed profile on the panel face hides small dents over time. The shell takes wind load at an exposed gate without a separate frame. Panel sizes follow the same rules as our store fixtures builds.

Window and Access

One aluminium sliding window faces the traffic lane, at 1,100 mm from the floor. The glass is 6 mm tempered, and a half-open position keeps rain out. A small exterior sill carries a clipboard or a radio. The steel door opens inward, with a mortise lock and two keys. A guard booth needs one clear exit, so the door swing stays inside the shell. Glass and frame details match our display cases work.

Specification Detail
Overall size 1200 W x 1200 D x 2400 H mm
Wall 50 mm sandwich panel, white steel face
Frame Galvanised steel, bolted corners
Window Sliding aluminium, 6 mm tempered glass
Door Steel with mortise lock
Base Steel plinth, 150 mm lift
Floor 18 mm cement board, vinyl finish

Floor, Power and Air

The floor is an 18 mm cement board on a steel frame, with a vinyl sheet on top. A 100 mm conduit runs from the base to the roof for power. Two sockets sit at 1,000 mm, and a light point hangs from the ceiling. A vent grille on the wall brings air through, and a small fan moves it in summer. The guard booth weighs about 320 kg, so a crane or a forklift lifts it. Our display tables use that same 18 mm board.

Placement on Site

Set the booth beside the lane it controls, within 3 m of the barrier arm. Keep 900 mm free at the door, so an officer steps out without turning. A guard booth faces the traffic flow, not the site office. Run the power cable before the plinth is fixed, since the guard booth base sits on a slab. Most sites pour a 100 mm pad under the four feet. A ticket counter often stands nearby, as on our cash wrap counters page.

Why Buy This Booth

A guard booth is cheaper than a built room and it moves with the site. The panels unbolt, and a crane lifts the shell onto a truck. Glass, door and frame stay dry, so the finish lasts through winter. List price starts at USD 7,200 for the 1.2 m unit. Our Shenzhen factory builds guard booth shells to your gate layout and glazing plan. Send the pad size and the window side through contact us, and we cut the panels to match.

Reviews

There are no reviews yet.

Be the first to review “Chalk White Guard Booth with Sliding Window, 1200 mm”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop