UniqueKiosk · Shenzhen workshop

Gable Three Tier White Laminate Display Table

$420.00

Retail display table with three white laminate levels on a centre block base. Price range: USD 420-760, set by width and level count.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Three Levels

This retail display table stacks three laminate boards on a stepped base. The bottom level runs 1200 mm wide. The top level runs 700 mm, so the shape steps back as it rises. A shop sets folded stock on one level and shoes on another. A retail display table of this shape shows three sizes in one view. The step leaves a clear edge on each tier, so a label reads from the aisle. Levels sit at 300 mm gaps and a customer reaches the top without a step. Retail display tables list this level plan.

Laminate Build

Each board on this retail display table is an 18 mm core with a white matte laminate face. A board takes 25 kg and does not bow at the centre. The edge is banded and sealed, so a chip does not lift the face. A retail display table with a matte finish hides a finger mark better than a gloss. Two centre blocks carry the upper levels and sit flush with the board edge. The base block runs 700 mm and holds the stack stable under a full load. Display tables use this board gauge.

Assembly

The unit ships as four parts with a set of cam fittings. One person assembles this retail display table in about twenty minutes. Blocks sit on dowels and lock with cams from below, so no bolt shows on the face. A retail display table of this build stays square after a move. Feet sit under the base block and take up a floor gap. The parts stack flat for a van, which suits a road show and a market stall. Read our bench notes for the build detail.

Specification Detail
Width 1200 mm
Height 1200 mm
Depth 500 mm
Levels 3 laminate boards
Board 18 mm core, matte face
Finish White laminate, banded edge
Load 25 kg per level

Store Use

Boutiques use this retail display table at the entry and set the new line on the top level. A denim shop stacks three rises of jeans and shows the wash grade. A shoe shop puts pairs on the lower tier and a single on the top. A beauty counter uses the levels for box sets. Display stands pair with this base width. A shop with a short wall likes the step shape, since the table reads full without a tall fixture.

Finish and Care

The laminate comes in matte white, light grey or warm oak tone. A white face suits a clean room and a pale wall. An oak face reads warm under shop light. A retail display table with a laminate face takes a wet cloth and no polish. A shop can swap one board later if the face wears. The blocks carry the same laminate, so the unit reads as one piece. A shop can also match it with our store display shelves.

Sizes and Price

Width runs at 900 mm, 1200 mm or 1500 mm. Height runs at 1200 mm or 1400 mm. Level count runs from two to four for this retail display table. Base depth runs at 500 mm or 600 mm. A card rail, a back panel and a caster set are options. A shop can also order a version with one glass top level. List price starts at USD 420 for the three level unit. ukiosks builds this retail display table in Shenzhen to order, so send your drawing through contact us.

Reviews

There are no reviews yet.

Be the first to review “Gable Three Tier White Laminate Display Table”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop