UniqueKiosk · Shenzhen workshop

Copperleaf Rotating Watch Display Carousel with Three Tiers

$2,100.00

Stainless steel rotating watch display carousel with three glass tiers and guards, driven by a slow motor. Price range: USD 2,100-3,200, set by tier count.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Round Form

This watch display carousel stands 900 mm tall on a 900 mm round drum. The three tier plates sit above the drum on a centre column. A customer walks the case and the tiers turn past a fixed sight line. A watch display carousel at this height suits a shop with a central island. The drum takes the motor and the wiring, so the floor stays clean. A shop can also run the unit as a static case when the motor is off. A watch display carousel also suits a launch table. Countertop displays list this drum size. Jewellery displays list this drum size.

Tier Plates

Three clear glass plates form the display of this watch display carousel. Each plate runs 840 mm across and carries six watch cushions. A glass guard sits on the plate edge at 180 mm tall. The plates sit at 60 mm gaps, so a strap reads from either side. A shop sets a brand on the top plate and a price card at the centre. The plate edge is polished and the guard is bonded at the corner. Display cases use this glass grade.

Motor and Light

A 12 volt gear motor sits in the drum and turns the tiers at 4 rpm. The motor runs quiet, so a shop keeps it on all day. A ring light sits above the top plate and runs at 4000 K. A watch display carousel with a lit ring shows the dial marks clean. A switch sits on the drum face and takes one press to stop. The unit draws under 30 watts and runs from a wall adapter. Countertop displays use a similar driver.

Build Details

The drum uses a 1.2 mm stainless sheet over a steel frame with a brushed finish. A base ring takes the weight and sits flat on tile. The column is machined and carries the plate bearings. A watch display carousel of this build holds 18 cushions in total. The drum face carries a small seam, and the seam sits away from the customer side. Each unit leaves the bench after a motor run and a balance test on the plates.

Shop Use

Watch boutiques put this watch display carousel near the entrance and let it turn during peak hours. A department store uses one for a single brand launch. A jeweller pairs a carousel with a glass counter and keeps the stock behind. A duty free shop sets the unit on a plinth so the tiers read at eye level. Store fixtures pair with this drum height. A shop with a small floor likes the round shape, since it takes one footprint.

Order and Price

Tier count runs from two to four. Drum diameter runs at 800 mm or 900 mm. Height runs at 900 mm or 1000 mm. The finish comes in brushed steel, black powder coat or a brass coat. A ring light, a slow motor and a glass guard are standard for this watch display carousel. A shop can also order a locking cover for the night. List price starts at USD 2,100 for the three tier unit. ukiosks builds this watch display carousel in Shenzhen to order, so send your drawing through contact us.

Specification Detail
Drum Diameter 900 mm
Height 900 mm
Tiers 3 glass plates
Plate Size 840 mm across
Motor 12 V, 4 rpm
Light 4000 K ring light
Load 18 watch cushions

Reviews

There are no reviews yet.

Be the first to review “Copperleaf Rotating Watch Display Carousel with Three Tiers”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop