UniqueKiosk · Shenzhen workshop

Pastry Counter in Fluted Wood With Curved Glass Case

$2,300.00

Fluted wood bakery counter with a marble look top and a curved two shelf bread case, sized 2.4 x 0.7 m for cafe and bakery fronts. Price range: USD 600-2,500, set by length and case count.

  • Any size, any finish – quoted from your store plan.
  • Shop drawings and a 3D layout before we cut.
  • Crated for sea or air freight, installed on site.

Description

Fluted Slat Base

Vertical wood slats form the base of this bakery counter. Each slat is 35 mm wide with a 10 mm gap, so lines read clean. Slats sit on an 18 mm plywood carcass and stop at a low kick rail. The kick rail keeps mops and trolleys off the timber. Two end panels close the run in flat wood. Slats are sealed twice, so flour and milk wipe away. A 2.4 m run needs about 52 slats, cut from one board batch. Small shops use this bakery counter as a front piece.

fluted pastry counter

Marble Top and Case

The top uses a 12 mm marble look compact laminate. It reads like stone but weighs far less than a slab. Edges carry a 20 mm trim in the same finish. A curved glass case sits on the right half, 1,000 mm long. The case has two shelves and a stainless frame. Bread and pastries stay covered but visible from the queue. This bakery counter leaves 1,400 mm of clear top for trays and till. display cases in flat front styles take the same shelf rails.

bakery counter front view

Back Bay and Service

A steel frame bay rises behind the counter to 1,600 mm. Three shelf lines hold bread boards, jars and bags. The bay sits 200 mm back, so it never blocks the case. A till stands on the clear top, close to the right end. Cash and bags go into a drawer under the deck. Staff serve from behind the case, facing the door. A bakery counter with a rear bay keeps stock off the top. Tongs and bags stay within reach.

bakery counter side profile

Build and Finishing

Carcass boards are 18 mm ply with a moisture resistant core. Slats are cut, sanded and sealed twice before assembly. The top sheet is glued and edge trimmed on site or in the shop. Steel bay frames are 25 mm tube, powder coated. Glass on this bakery counter is 5 mm tempered and curved in one piece. Every bakery counter is checked for square before packing. cash counter drawers can replace the left slat bay. countertop cases cases can sit on the clear top.

fluted slat top detail

Fit and Delivery

The unit measures 2.4 m by 0.7 m, with a top height of 950 mm. It suits cafe fronts and bakery corners with 1.4 m of aisle behind. One crate holds the counter, about 120 kg. The glass case ships boxed apart, so nothing rests on the frame. Site work is setting the counter, then fixing the case and the bay. Two people need about three hours. A 16 A circuit runs the case LED strip. retail display fixtures clearance rules apply at both ends.

Price and Custom Build

Fluted bases cost more labour than flat panels, and they hide scuffs well. A curved case lifts plain bread into a display piece. The marble top takes hot trays without marks. List price starts at USD 2,300 for the 2.4 m run. A shorter bakery counter at 1.7 m lands near USD 1,650. ukiosks builds this bakery counter to order in Shenzhen. We can reset run length, slat width, case size and bay height. Send your plan and we return drawings and a quote. Nearby food and drinks and coffee fit-outs fronts use the same slat module.

Specification Detail
Overall size 2.4 x 0.7 x 0.95 m (custom 1.7-3.0 m)
Base 35 mm wood slats on 18 mm plywood
Counter top 12 mm marble look laminate
Display case Curved glass, two shelves, 1,000 mm
Back bay Steel frame with three shelf lines
Kick rail Wood finish, 80 mm
Packing One crate, about 120 kg

Reviews

There are no reviews yet.

Be the first to review “Pastry Counter in Fluted Wood With Curved Glass Case”

Your email address will not be published. Required fields are marked *

Material Steel frame with chrome, brass or powder-coated finish
Size Standard size as listed. Custom lengths and heights on request
Build time Sampling in 7 days, production in 25 to 30 days
Packing Wrapped, crated and palletised for sea or air freight
Minimum order One unit. Volume pricing from ten units
Drawing Shop drawing and 3D layout sent before cutting
Quick enquiry

Send us your plan

Fixture, size, quantity and where it ships. We reply within one working day.

On this page

01

Made to size

Any length, height or shelf count. Send a sketch and we quote that size.

02

Drawings first

Shop drawings and a 3D layout come before cutting. You approve every joint.

03

Crated for export

Every unit is wrapped, crated and palletised for sea or air freight.

04

Install support

Our team installs, or we brief your fitter with photos and a pack.

More fixtures from the shop